Hello and Welcome, There may be no more important tools in my shop/garage than my selection of Brass Brushes. I have known about using (fine) brass brushes to minimize scratching to chrome for a long time. So long in fact, I do not remember who taught me that. I suspect it was my father. I can remember him using brass-wool on an old Winchester 32/40 half round in about 1968. The barrel of the old Winny had been shortened in about 1905. So cleaning off the old patina at that point really did not matter.
Left Click on Images to Enlarge. Use Back (<) Button to Return
Above: Removing the surface rust from a chrome seat post using a fine brass wheel-brush mounted on a 18 volt rechargeable drill. Originally I used a 4&1/2 inch angle grinder with a brass wheel brush. But the drill being much slower seems to be mimic hand brushing the chrome better than the high-speed grinder.
And the drill is also much safer, a lot less brass frag flying around.
Above: After brushing I used the Turtle-Wax Chrome Polish and Rust Remover. Then I touch it up with the brush then buff (again) with a rag. As you can see the old seat-post really pops now!
Above: As you can see, the brass brushes come in a variety of sizes. I mainly use the wheel-brush and the detail brush (smaller wood handle brush). But on deeper or heavier rust, I`ll use the bigger hand brushes as well. I also have a tiny brass brush attachment for my Dremel type tool. But honestly I don`t use it much.
Above: Pedals are where the brushes really shine. The wheel-brush will do most of the work. But the detail brush is a must for the inner surfaces.
Above: The same two pedals after brushing and polishing. I also used the Turtle Wax Chrome Polish and Rust remover on these.
Above: Sometimes it is something as simple as this seat-post collar bolt and nut. As you can see it looks pretty shabby.
Above: The same collar bolt and nut after just a few minutes with the brass wheel-brush. It is the details that will take your restorations to the next level. What a great chemical free way to clean-up a nasty looking small part.
Above: A section close-up of a handlebar from a bike I am currently restoring. This is a perfect job for the brass wheel-brush. I sometimes leave the stem attached and use it like a handle. This also allows me to leave the vintage grips alone. Thats a big plus when the grips are in excellent condition.
Above: The same handlebars after brushing and polishing. I was able to loosen the brake levers, slide them out of the way. Then after brushing, polishing and buffing the area I just slide them back into place. I was also able to wheel -brush the levers while they remained on the handlebars as well. And of course the whole assembly got the Turtle Wax treatment too. I did remove the shifters for cleaning and polishing.
Above: A close-up of a section of the front wheel on the same ladies bike I am restoring now. (along with the Giant and the Parliament) I hand brushed these rims. I think it is easier to damage the rims with the wheel-brush attachment. And when the rims are boarder-line as to being savable or not, the hand brush just works better for me. I am more likely to use the wheel-brush on a higher quality chrome steel wheel. (like an old Schwinn) This wheel belongs to a Free-Spirit.
Above: The front wheel after brass brushing and polishing with Turtle-Wax. The fender struts were also brushed and polished as were the hubs and flanges. The spokes were cleaned (one at a time) with Armor-All cleaning wipes.(twice) A few of the spokes might get touched-up latter with fine wet sanding paper. Any spokes that get sanded will also get polished with spray detailing wax on a rag.
Above: Probably the most important part of this post. I position a fan to blow the dust away as I am brushing. I also have a exhaust fan in the gable that comes on automatically when the lights are turned on. I position the fan so that it blows the dust in the general direction of the exhaust fan. The floor fan does not have to be set on high, mine is usually on low. I know this works well because I have Asthma. If it did not work I would be the first to notice.
Above: The rack and struts and saddle springs. 25 years of storage has left them with a light coat of surface rust. Not bad at all considering.
Above: The same area after brushing and polishing. The rack and saddle were removed for brushing. I took the saddle hardware apart (except the springs) for brushing as well.
Above: A before shot of the rear brake caliper. The brake calipers were removed for brushing and polishing too.
Above: An after shot of the rear brake caliper. I did not take these calipers apart completely. First I scrapped the old brake shoes. Then I just released the return spring and brushed them with the detail brass brush. Then I polished the calipers with Turtle-Wax.
Above: I Do Not Brush Alloy Components. These calipers were removed, taken-apart and cleaned and Polished with Mother`s Mag and Aluminum Polish. Mothers works on straddle cables too.
I hope you found something useful here. The Giant is pretty much finished, I will be posting it soon. Also, about the Parliament. I just had the original rear hub serviced by my friend Joe in Pontiac Mi. He is the only one who still had the correct removal tool for the free-wheel. He has been at the bike shop for as long as I was in Masonry, which is about 32 years. He has been a big help to me on more than one occasion. So if your ever over near Wide-Track and Perry in Pontiac Mi. stop in and say hello. There are not many around like Joe anymore. He reminds me of the guys at Powers Schwinn in RoyalOak Mi about 45 years ago.
Until Next Time, Ride Safe and Remember to Always.. RESCUE, RESTORE & RECYCLE
Cheers,Hugh
No comments:
Post a Comment